Hydra-Rester 1

Hydra-Rester 1" MIP Water Hammer Arrestor

Hydra-Rester 1

Hydra-Rester 1" MIP Water Hammer Arrestor

Hydra-Rester 1" MSWT Water Hammer Arrestor

What is Water Hammer?;; Although water hammer is a subject usually left up to plumbing engineers, the effects of water hammer must be dealt with every day by plumbing contractors everywhere. Water hammer is easily recognized by the banging or thumping noise that’s heard when valves are shut off. Although this is an easy way to recognize the problem, water hammer doesn’t always make these telltale noises. Water hammer occurs when the flow of moving water is suddenly stopped by a closing valve. This sudden stop results in a tremendous spike of pressure behind the valve which acts like a tiny explosion inside the pipe. This pressure spike reverberates throughout the plumbing system, rattling and shaking pipes, until it is absorbed. Normally, a sufficient pocket of air will absorb such a pressure spike, but if no pocket of air is present, expensive fixtures and appliances within the plumbing system will be damaged as they are left to absorb this pressure spike.;; Why Air Chambers Don’t Work;; It used to be thought that an air chamber, or capped stand pipe, was an effective solution to controlling water hammer. However, within an air chamber, nothing separates the air from the water. It only takes a few short weeks before the air is absorbed into the water, leaving the air chamber waterlogged and completely ineffective. Laboratory tests confirm that the air is depleted by simple air permeation and by interaction between static pressure and flow pressure. In the diagram shown, (left) notice the difference in water level between static line pressure and post-cycle static level.;; Controlling Water Hammer;; The most effective means of controlling water hammer is a measured, compressible cushion of air which is permanently separated from the water system. Sioux Chief arresters employ a pressurized cushion of air and a two o-ring piston, which permanently separates this air cushion from the water system. When the valve closes and the water flow is suddenly stopped, the pressure spike pushes the piston up the arrester chamber against the pressurized cushion of air. The air cushion in the arrester reacts instantly, absorbing the pressure spike that causes water hammer. Although arresters are typically tested to 10,000 cycles, Sioux Chief arresters have been independently lab tested to withstand 500,000 cycles without failure. All Sioux Chief arresters are guaranteed to control water hammer for the lifetime of the plumbing system.
$68.67
Brand: Sioux Chief
SKU
656-ES
  • Buy 4 for $63.39 each and save 8%
Hydra-Rester 1" MSWT Water Hammer Arrestor is available to buy in increments of 1
What is Water Hammer?

Although water hammer is a subject usually left up to plumbing engineers, the effects of water hammer must be dealt with every day by plumbing contractors everywhere. Water hammer is easily recognized by the banging or thumping noise that’s heard when valves are shut off. Although this is an easy way to recognize the problem, water hammer doesn’t always make these telltale noises. Water hammer occurs when the flow of moving water is suddenly stopped by a closing valve. This sudden stop results in a tremendous spike of pressure behind the valve which acts like a tiny explosion inside the pipe. This pressure spike reverberates throughout the plumbing system, rattling and shaking pipes, until it is absorbed. Normally, a sufficient pocket of air will absorb such a pressure spike, but if no pocket of air is present, expensive fixtures and appliances within the plumbing system will be damaged as they are left to absorb this pressure spike.

Why Air Chambers Don’t Work

It used to be thought that an air chamber, or capped stand pipe, was an effective solution to controlling water hammer. However, within an air chamber, nothing separates the air from the water. It only takes a few short weeks before the air is absorbed into the water, leaving the air chamber waterlogged and completely ineffective. Laboratory tests confirm that the air is depleted by simple air permeation and by interaction between static pressure and flow pressure. In the diagram shown, (left) notice the difference in water level between static line pressure and post-cycle static level.

Controlling Water Hammer

The most effective means of controlling water hammer is a measured, compressible cushion of air which is permanently separated from the water system. Sioux Chief arresters employ a pressurized cushion of air and a two o-ring piston, which permanently separates this air cushion from the water system. When the valve closes and the water flow is suddenly stopped, the pressure spike pushes the piston up the arrester chamber against the pressurized cushion of air. The air cushion in the arrester reacts instantly, absorbing the pressure spike that causes water hammer. Although arresters are typically tested to 10,000 cycles, Sioux Chief arresters have been independently lab tested to withstand 500,000 cycles without failure. All Sioux Chief arresters are guaranteed to control water hammer for the lifetime of the plumbing system.

  • Connection Size: 1"
  • Unit Size: E
  • Length: 13 1/2"
  • Width: 2 1/8"
  • Male Sweat / Press Fitting
  • Fixture Unit Value: 114-154
  • No Lead
  • Arrester body: type L copper tube
  • Piston: poly piston with two EPDM o-rings
  • Male thread fitting: copper MIP thread
  • Piston lubrication: Dow-Corning, 111 FDA approved silicone compound
  • Max working temperature: 250°F
  • Max working pressure: 350 PSIG
  • Burst tested: to 2,900 PSIG
  • Sweat connection: Compatible with Press Fittings or Push Fittings
More Information
Manufacturer Sioux Chief
Size 1"
Material Copper
Connection Sweat
Length 13 1/2"
Max Pressure (PSI) 350
Max Temperature 250°F
Write Your Own Review
You're reviewing:Hydra-Rester 1" MSWT Water Hammer Arrestor
Your Rating